trickluvdakid
@trickluvdakid
Active Member
Topics: 0 / Replies: 19
Reply
RE: Composite LCD Controller Board Support

Still need to configure the controls. Right now only the d-pad/directionals work. But I'll get it done! Thanks again all for your help. The next bu...

8 years ago
Reply
RE: Composite LCD Controller Board Support

Thanks for the response. I ended up wiring it to the converter. So far so good

8 years ago
Reply
RE: Composite LCD Controller Board Support

So, use the pads to solder (on the bottom side of the board) as shown in this picture? Also, is 24awg overkill for the LCD and Batteries? Thanks for t...

8 years ago
Reply
RE: Composite LCD Controller Board Support

Following on your guide for V3, can I just splice the power and ground into the power and ground on the controls?

8 years ago
Topic
Replies: 13
Views: 2659
Reply
RE: 2017 PSP Project

Making some progress... Adam, I seem to have lost this : Mini Switch (the same as the original PSP Wifi switch) for switching the audio on and off (op...

8 years ago
Reply
RE: 2017 PSP Project

Posted by: othermod It's probably a leftover from a previous version of the board. Most of the cheap buck converters use a diode in their function. T...

8 years ago
Reply
RE: 2017 PSP Project

Posted by: trickluvdakid Started my project, but ran into a roadblock. Need to order a new audio jack. The teardown PSP I was using, the audio wa...

8 years ago
Reply
RE: 2017 PSP Project

Started my project, but ran into a roadblock. Need to order a new audio jack. The teardown PSP I was using, the audio was crackling. So, I ordered ...

8 years ago
Reply
RE: 2017 PSP Project

Thanks for the help. I'll get a good start on this Saturday.

8 years ago
Reply
RE: 2017 PSP Project

There was a 0.7V drop across the diode. I removed the diode, bridged it, and I now have 5V from the input to the resistor. Not having the diode should...

8 years ago
Reply
RE: 2017 PSP Project

Thanks, helps to have the right tools. Should've used wire to bridge it, but solder works too. OK...so... Setting my power supply at 5V resulted in 4...

8 years ago
Reply
RE: 2017 PSP Project

Did not try. Removed the buck and there is continuity from pin 2/3 to the resistor. Will hook up to 5V after lunch to verify.

8 years ago
Reply
RE: 2017 PSP Project

Did some continuity checks, and I agree with your drawing. Removing the buck and jumper pin 2 > pin 3 looks correct. Working on this right now, wil...

8 years ago
Reply
RE: 2017 PSP Project

Not yet. If not tomorrow, I will this weekend. I did notice the same regulator, but the boards that Allen and I ordered were different. Thought that...

8 years ago
Reply
RE: 2017 PSP Project

Pulled the back off of the LCD I ordered. Completely different. I did use the link that you have on your store page, so I'm guessing you will have t...

8 years ago
Reply
RE: 2017 PSP Project

I'll be starting mine on Sunday. Let you know what I see when I tear it apart.

8 years ago
Reply
RE: 2017 PSP Project

Ok, I ordered my LCD (same one from the link) on Jan 4th and it arrived yesterday, Jan 25th. All of the small parts I've ordered have been about 1 1/2...

8 years ago
Reply
RE: 2017 PSP Project

Waiting on the same LCD on Jan 4. I've ordered everything I need, and the LCD is the only thing that wasn't provided with a tracking number. I'll keep...

8 years ago